By Susan Pevaroff Berschler and Bob Vila | Updated Sep 28, 2020 12:19 PM

Natural stone, with its rich colorations and wonderful feel, is Mother Nature’s gift to our homes. But this beautiful, popular kitchen and bathroom countertop option is pricey—and for all its durability, it’s got a delicate side. That’s why it’s crucial to protect your investment by caring for marble correctly. This guide will take you through how to clean marble countertops, address stains, and seal the surfaces regularly, but first face a stone cold fact: Marble, composed mainly of calcium carbonate, is sensitive to acidic solutions. This means any acid, whether a splash of lemon juice, a damp margarita glass, or an acidic cleaner such as vinegar, can eat away at the surface, creating dull spots known as etches. Some folks consider etches part of a countertop’s character, while others opt to grind down the top layer and re-polish the surface when enough etches accumulate. So strive to keep your countertops an acid-free zone, and now read on to become a master in marble protection and maintenance.

General cleaning is so simple—another reason for marble’s popularity. Just be sure to avoid products containing acid, including lemon juice and vinegar. Though you can buy non-abrasive stone cleaner specifically tailored to marble, still read labels carefully to avoid damaging your surface. Alternatively, you can save money and use a mild, non-abrasive, pH neutral (non-acidic) soap mixed with water, which is all you really need to clean marble countertops.

MATERIALS AND TOOLS Available on Amazon – Marble stone cleaner – Warm water – Gentle dish soap – Spray bottle – Dish cloth – Soft, absorbent towel

If not using marble cleaner, mix a squirt of gentle, non-abrasive dish soap with warm water in a spray bottle and spray the counter generously. Scrub gently and wipe soapy solution off with a clean wet cloth. Repeat process until all soapy residue is gone.

Rub the countertop dry, and buff with a soft absorbent towel.

Banishing stains from marble can be trickier than a routine cleaning. The key is correctly identifying the origin of the stain and then applying the appropriate chemical or poultice (a paste-like cleaning agent). Think of the materials listed below as your stain-fighting arsenal. Note, too, that the sooner you address a stain, the better your chance of getting rid of it.

Caution: Never mix cleaning agents or chemicals, as the result can be toxic, even lethal. Before cleaning, always test the cleaning agent on an inconspicuous location to determine its suitability and make certain it does not damage the surface. Wear appropriate clothing such as gloves and protective eyewear, and work in a well-ventilated area.

MATERIALS AND TOOLS Available on Amazon – Soft liquid cleanser – Mineral spirits – Acetone – Ammonia – 12 percent hydrogen peroxide solution – 20 percent hydrogen peroxide solution – Bleach – Lacquer thinner – 0000-steel wool pads – Razor blade – Sponge – Gloves – Protective eyewear – Flour – Pre-mixed commercial poultice

An oil based stain like grease, cooking oil, milk, or makeup will darken the stone and must be dealt with chemically. Clean gently with one of the following: soft, liquid cleanser with bleach, ammonia, mineral spirits, or acetone.

Address coffee, tea, wine, fruit, tobacco, paper, and most other food stains (which generally have a pinkish-brown appearance) with a 12 percent hydrogen peroxide solution and a few drops of ammonia. Wipe over the stain with a clean cloth. Rinse with a wet cloth and dry with a chamois.

Combat mildew stains with a solution of three parts household bleach with one part water and a dash of dishwashing detergent in a spray bottle. Mist the surface thoroughly and repeat application until the stain disappears. Rinse with clean clear water and dry.

To remove ink stains from dark colored stone, dip a cotton swab in acetone and apply directly to the surface. For lighter colored stone, use a 20 percent hydrogen peroxide solution. Keep a soft cloth or sponge dampened with water handy to wipe away the cleaning agent promptly after the stain has been removed. Treating large volume ink stains or those that have set in requires a poultice.

Remove a small drip with lacquer thinner dabbed on with a clean cloth or scrape it off carefully with a razor blade. A larger paint stain will require a commercial paint stripper that could cause etching and may require re-polishing after removal. Follow the manufacturer’s directions for use of these products, and flush the area thoroughly with clean water. Be sure to ventilate the area and wear rubber gloves and eye protection.

Buff out water spots with a dry, 0000-rated steel wool pad. That same pad may do the trick for smaller scratches and nicks. Larger problems may require re-polishing. In future, use coasters and trivets on counters.

Metal stains caused by iron or rust range from orange to brown in color, while copper or bronze stains will be green or muddy brown—all are stubborn, deep-seated rust especially. Tackle with a poultice:

Because marble is porous, a sealant is recommended as a barrier that can possibly keep a spill from becoming a stain. Experts suggest re-sealing every three to six months, but quality sealing products, available from any home improvement retailer, are simple to apply.

MATERIALS AND TOOLS Available on Amazon – Mild dish soap – Single-edged razor blade – Plastic scraper – Chamois – Clean cloths – Acetone – Impregnating or penetrating sealer for marble countertops

Clear everything off the counters so the entire surface is accessible. Clean the surface with mild dish soap. Dry with a clean cloth.

Remove any built-up residue from cleansers, cooking grease, or other substances might remain with a plastic scraper or (carefully!) a single-edged razor blade. To use a blade, hold it at an angle and lightly pass it over the marble.

Use acetone, if necessary, to strip off old sealer and remove residues from such products as window cleaners. Apply with a clean cloth and rinse with wet cloth, then dry with a chamois—do not let the counter air dry.

Read and follow all directions on the sealant’s packaging. In most cases, application is a matter of pouring the sealer directly onto the surface and spreading it evenly with a clean white cloth. Leave it to soak for the time specified in your products directions, usually around three to four minutes.

Sprinkle additional amounts of sealer over the treated areas. This will allow you to easily collect and gather excess sealer during cleanup. Use a clean dry cloth to remove any sealer that has not soaked in.

Apply a second coat of sealer only if your product’s specific directions indicate it is necessary. Otherwise, one coat will be enough.

Disclosure: BobVila.com participates in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for publishers to earn fees by linking to Amazon.com and affiliated sites.

Copyright © 2022 Acton Media Inc. All rights reserved.